Humboldt County’s Own Purple Maxx 0-0-3
Amino acid based cocktail that intensifies final color in susceptible varieties. No dies, no tricks. Don’t wait and hope. Get the color you want when it’s time to harvest. Customers say many new varieties respond very strongly and reliably to Purple Maxx.
Directions: This product usually causes a massive uptake of nutrients so fertilizer solution should be cut back by about 1/3
- Soil - This product usually causes a massive uptake of nutrients so fertilizer solution should be cut back by about 1/3. - (1): If you are close to the end of the flowering cycle it would be best to feed Purple Maxx without fertilizer. Use 1/2 to 1 tsp. of Maxx per gallon of water right up to the end. If you have good air circulation you can spray with 1/2 to 1 tsp/gallon. Some testers have used a lot more. If powdery mildew is an issue add Serenade to the mix. - (2): If you are just starting the bloom cycle, use 1/2 to 1 tsp. per gallon of water and apply about once a week or foliar feed with 2ml /gallon (1 tsp 2 1/2 gallons of water). If plants show no sign of tip burn, nutrient strength can be increased.
- Hydro - Purple Maxx works well in hydro at the rate of 2 1/2 to 5 ml / gallon. DO NOT USE AN AERATOR! It will cause bacterial contaminants that may be present in the reservoir to grow drastically although some testers have reported that problems can be controlled by adding 2-5 ml. of 35% hydrogen peroxide per gallon of water to the reservoir. Others have avoided problems by adding the Maxx 24-48 hours before reservoir change. The safest way is to use the foliar feed method as far into bloom as possible.
Humboldt County’s Own Snow Storm Ultra 0-0-3
With an amino acid profile unique in the industry, Snow Storm consistently produces intense resin, fragrance and flavor plus the well known “frosted", look that growers love. Works on all varieties. Not a carbohydrate or sugar water product. This is the real deal from “old school", Humboldt County.
Directions: It's important to not overfertilize. It's never necessary to run nutrient concentration above 1000 ppm.
- Soil - Start applying during the vegetative stage at the rate of 1/2 tsp. per gallon of water. Continue at this rate until 3 or 4 weeks into bloom and then increase to 1 tsp/gallon. The last 3 weeks of bloom the dose can be increased up to 2 tsp/gallon.
- Hydro - Use 1/2 tsp per gallon and run continuously. Be cautious if running nutrients over 800-1000 ppm. For example, running 5 ml/gallon at 1200 ppm can drop reservoir to 800 ppm in 24 hours. Some strains can take it, some can't.
- Foliar: Much more economical. Use 1/2 to 1 tsp per gallon of water and apply once a week. Use caution once flowers bulk up.
Humboldt County’s Own Deep Breath 0.1-1-1
This honey and vitamin based cocktail, “primes the pump", during the vegetative and early bloom stage so plants experience an explosive surge in bulk when G10 is applied. The DEEP BREATH/ G10 combo boosts yields to unheard of levels. Even beginners will see incredible effects in 2 weeks.
Directions:
- Soil - beginning in the vegetative stage use 5 ml (1 tsp) per gallon of water and apply every watering or every other watering and continue through the second week of bloom. Third week switch to G10 (Gravitation #10).
- Hydro - Use 2.5 to 5 ml. (1/2 to 1 tsp.) per gallon of water on the same schedule as above. If you're running a reservoir longer than 5 days, add an extra 2.5 ml./gallon of water after 5 days. Third week switch to G10 (Gravitation #10)
Bluelab pH Pen
Perfect for quick and easy pH and temperature readings direct from your solution. The Bluelab® pH Pen is the preferred option for hand held pH meters. It provides a compact, quick and handy way to manage the success of your crops to ensure maximum uptake of nutrients.
A key parameter that affects nutrient uptake is whether your solution is acid or alkaline, which is measured in pH. Teamed with our Bluelab® Conductivity Pen you have a robust, convenient and accurate measurement system.
pH Pen Features:
- Measures pH and temperature with selectable units for °C and °F
- Backlit LCD display
- Double junction probe (not replaceable)
- Successful calibration indicator
- Hold reading function and low battery warning
- Fully waterproof with auto off function and automatic temperature compensation
- Bluelab pH Probe KCI Solution, Bluelab pH 7 and Bluelab pH 4 Solution Sachets included
- Range: 0.0–14.0 pH/0–50°C/32°–122°F
- Resolution: 0.1 pH/1°C/1°F
- Accuracy @ 25°C: ±0.1 pH
- Battery type: 1 x AAA alkaline.
Bluelab In-Line pH Probe
Replacement probe only - Bluelab Guardian Monitor Connect In-Line sold separately
Threaded probe heads allow for simple installation direct into an irrigation line for effective in-line measurements. Suitable for use before or after mechanical injectors.
Both conductivity and pH probes can screw directly into female 1” NPT pipe fittings on monitor using the adapter included in monitor kit.
In-line pH probe cable length: 3 meters / 10 feet
Select options
1Only 1 left!
Bluelab In-Line Monitor
The Bluelab Guardian Monitor Connect In-Line is not only a constant indicator of the desired levels of pH, conductivity and temperature of your nutrient solution, it also data logs these critical parameters to your computer for you. It does not stop there. You can access the data via the cloud from a remote mobile device or computer to check for extreme variances to ensure these critical parameters are hitting the mark for crop success. For remote or cloud access, the computer you are already data logging to will need permanent internet access.
Threaded probe heads allow for simple installation direct into an irrigation line for effective in-line measurements. Suitable for use before or after mechanical injectors. Both conductivity and pH probes can screw directly into female 1” NPT pipe fittings using the included adapter.
Teamed with the Bluelab® Connect™ Stick, you get all the convenience of wireless data logging and remote alerts.
Monitor Features:
• pH and EC in-line threaded probes to fit into in-line plumbing
• Remote viewing with Bluelab® Connect™ Software and Apps
• Replaceable double junction high pressure pH probe included
• Bright, plant-safe green LED with adjustable brightness
• Easy to navigate menu to program & adjust settings
• Selectable conductivity and temperature scales
• Simple push button pH calibration
• No calibration required for conductivity and temperature (factory calibrated)
• Flashing high and low alarms (non-audible)
For more information, see Data Sheet and Instructions.
Select options
12Only 12 left!
Bluelab Conductivity Pen
The Bluelab® Conductivity Pen simply tells you the amount of nutrient in your solution. Conductivity is automatically compensated with the integrated temperature sensor, providing a compact, quick and accurate way to measure two key parameters for crop health.
Teamed with our Bluelab® pH Pen you have a robust, convenient and accurate measurement system.
Conductivity Pen Features:
- Measures conductivity and temperature with selectable units for conductivity and temperature
- Backlit LCD display with low battery warning
- Successful calibration indicator and calibration is optional
- Fully waterproof with auto off function and hold reading function and automatic temperature compensation
- Units: EC, 500 ppm, 700ppm, ºC, ºF
- Range: 0.0–10.0 EC, 0–5000 ppm (500 ppm), 0–7000 ppm (700 ppm) and 0–50ºC/32–122ºF
- Resolution: 0.1 EC, 10 ppm (500 ppm), 10 ppm (700 ppm) and 1ºC/1ºF
- Accuracy @ 25ºC: ±0.1 EC (@ 2.77 EC), ±50 ppm (500 ppm) (@ 1385 ppm), ±70 ppm (700 ppm) (@ 1940 ppm) and ±1ºC / ±2ºF
- Battery type: 1 x AAA alkaline
Select options
7Only 7 left!
Aeromixer Pump
Aeromixer is a pump made specifically for growers, by growers, with a dual purpose: to mix nutrients and aerate feeding solutions with just one pump. Aeromixer makes feeding large and smaller gardens a breeze and reduces the need for air stones, air pumps, and pH up and down additives.
Aeromixer Standard and Tall Specifications
- 3/4 horsepower motor
- Moves 4,450 gallons per hour
- Easily mixes tanks from 50-500 gallons (effective up to 3,000 gallons)
- Max height: 40 ft
- Max Submersion Depth: 17 ft
- Instructions
- 1/6 horsepower motor
- Moves 1,600 gallons per hour
- Easily mixes 15+ gallon tanks
- Max height: 20 ft
- Max Submersion Depth: 23 ft
- Instructions